Set of 3 molds - Holographic round Geode tray with coasters and holder

4.7

(676)

Write Review

$ 42.50

Add to Cart

Qty

In stock

Description

Three holographic silicone molds for: a large round geode tray. The tray is 28 cm (11") wide and 8 mm (1/3") thick. a set of four round Geode coasters. The coasters are 12.5 cm (5") wide and 8 mm (1/3") thick. a matching holder. This holder is suitable for the 4 Geode coasters. You insert the legs from the bottomside t

Three holographic silicone molds for:

a large round geode tray. The tray is 28 cm (11) wide and 8 mm (1/3) thick.
a set of four round Geode coasters. The coasters are 12.5 cm (5) wide and 8 mm (1/3) thick.
a matching holder. This holder is suitable for the 4 Geode coasters. You insert the legs from the bottomside through the slots of the base plate. You can fix the legs with a drop of glue or (UV) resin so that it becomes a solid piece (Tip: place the holder upside down, so that the legs will hang vertically while the glue or resin is drying).

Note: do not apply too thick a dome layer on the legs, because then they will no longer fit through the slots.

These silicone molds have holographic color effects, which will transfer to the surface of your resin artwork. The molds are also in a normal version available, without holographic effect.

Silicone mold for a set of four round coasters of 10 cm (4) wide and 8 mm (1/3) thick. There is also a mold available for a holder, see one of the pictures (for illustrative purposes, this item is only for the coaster mold).

Need more than four coasters in the holder? Then get the mold for longer legs too, so that eight coasters will fit into the holder.

It is also easy to make round coasters with a raised edge and an engraved pattern if you combine this mold with one of our round inlay molds.

The round coaster mold is also in a holographic version available, for spectacular color effects on the surface of your resin coasters!

Silicone mold for a set of four 'Fantasy' coasters. The coasters are 11.5 cm (4 1/2) wide and 8 mm (1/3) thick.

This mold is one of our molds with the Fantasy theme, which further consists of a coaster holder, 4 trays, 2 cakestands and a set of 8 medallions.

Several of these molds are in sets available, for special setprices.

The Fantasy coaster mold is also in a holographic version available, for spectacular color effects on the surface of your resin coasters!

Silicone mold for a set of four Holographic round coasters of 10 cm (4) wide and 8 mm (1/3) thick.

These coasters are the same as our normal round coasters, but then with a Holographic color effect, which will transfer to the surface of your resin coasters. We call this specific effect 'Color Burst'!

We also have a mold separately available for a holographic round coaster holder, see one of the pictures (for illustrative purposes, this item is only for the coaster mold).

Silicone mold for a set of four square coasters of 10 x 10 cm (4) and 8 mm (1/3) thick. There is also a mold available for a holder, see one of the pictures (for illustrative purposes, this item is only for the coaster mold).

Need more than four coasters in the holder? Then get the mold for longer legs too, so that eight coasters will fit into the holder.

It is also easy to make square coasters with a raised edge and an engraved pattern if you combine this mold with one of our square inlay molds.

The square coaster mold is also in a holographic version available, for spectacular color effects on the surface of your resin coasters!

Silicone mold for a set of four square Kintsugi coasters (Kintsugi is the Japanese art of fixing broken pottery). The coasters are 10 x 10 cm (4 x 4) and 8 mm (1/3) thick.

There is also a matching Kintsugi coaster holder available, which holds 4 coasters, and for a 25 cm (10) square Kintsugi tray, see some of the pictures (for illustrative purposes, this item is only for the coaster mold).

The 3 molds are also in two sets available (coasters with holder, coasters with holder and tray), for special setprices.