Pure Tough (Scratch & Heat Resistant Epoxy Coating) – SPACE Cabinets

Healthofmindart epoxy systems are the most advanced on the Australian market, what separates and gives us a point of difference to our competitors is that we have been makers and we understand what makers want. Our products are 100% Australian made and we have the documents to back this up. Keeping manufacturing in Aus
Healthofmindart epoxy systems are the most advanced on the Australian market, what separates and gives us a point of difference to our competitors is that we have been makers and we understand what makers want. Our products are 100% Australian made and we have the documents to back this up. Keeping manufacturing in Australia is extremely important to us not only because we have some of the most rigorous quality control in the world but we help keep our economy going. When you buy our formulas not only are you getting the highest possible quality as we are one of 2 actual Australian made products, but you are helping grow our country and maintain it's high quality manufacturing standards. Our epoxies are high end formulas designed for long term results. It is extremely important our customers know that our products are designed for long term results. ALL epoxy resins contain aromatic rings which cause long term darkening, cheap epoxies will discolour extremely quickly. Our systems have the most “acceptable amounts” of UV stabilisers and absorbers. For a while Stonecoat the US company has provided a tough epoxy coating for benches etc, well we have worked seriously hard on this new scratch and super tough epoxy coating system. This epoxy would be one of the most durable, hard and scratch resistant epoxies in Australia.  PURE TOUGH is a high gloss, low viscosity, self-levelling, solvent free two-pack coating designed as a hard-wearing top coat for timber, furniture, or art applications. PURE TOUGH achieves a high build in a single coat and provides an extremely durable, scratch resistant finish. Mix ratio: 2 parts A to 1 part B (vol) Work time: 15-30 minutes Film Thickness: 0.5 to 1mm per coat Coverage Rate: 0.5 to 1.0m2/L Recoat: 24-48hrs Light use: 36 hours Full Cure: 7 Days Colour Stability: Suitable for internal Shore D hardness: 75 VOC content: ≈0 g/L Application temperature: 10-35∞C heat resistant over 150 degrees  do not apply butane torches , heat guns only  Substrates should be thoroughly sanded or ground to provide a keyed surface.  If applying over existing coatings, adhesion should be tested by preparation of a small test area. Remove all potential contaminants. Contact HOM if unsure. It is generally recommended that the surface to be coated be elevated from the work area to allow the coating to drip freely off the sides. Ensure tape and protective sheeting is used to protect work area. Ensure that the surface is level. PURE TOUGH is designed to be applied by pouring or spreading to achieve a high build. Apply via brush or spreader. Material can be applied thinly via roller however multiple coatings will be required to achieve the desired result. If bubbles occur, they can be easily broken via use of a heat gun – bubbles should be removed within 30 minutes of application. Some timber can have rejection issues with natural oils, so between coats wipe down with metho then sand, then wipe down with metho using fresh towels constantly. Multiple coats needs to applied. First coat will seal the timber as timber has a pouress nature to it. Sanding between coats and wiping with metho is required.  Epoxies outside of Healthofmindart epoxies can have higher surfactants which can cause surface imperfections, wipe the surface with metho before re-coating.  Available in 1.5L 3L AND 6L.

Epoxy Resin for Art - Gallon Kits | Stone Coat Countertops

Superclear® Countertop Epoxy 2:1 - Superclear® Epoxy System

Pure Tough (Scratch & Heat Resistant Epoxy Coating) – SPACE Cabinets

To get the best performance in high temperature service applications, use High Temp Epoxy Surface Coat. Our #1096 High Temp Epoxy Surface Coat is a

High Temp Epoxy Surface Coat

The Unicone Art craft resin kit dries crystal clear with no yellowing over time. It's protective but not too thick, and it's easy to mix and pour. Low bubbles too!.

Extra Deep Pour Resin Epoxy Kit (2 to 4 inch Pours), 1.5 GL, UV Resistant, Low Odor, Crystal Clear, Bubble Free, 2:1 Art Casting Resin, River Tables

The Prepac Elite Home Storage Collection is a great choice for any kitchen, garage, laundry room, or anywhere else you may need some extra storage space. Elite cabinets are constructed using laminated composite wood and feature stylish brushed metal handles and adjustable hinges. MDF doors with profiled (rounded) edges add a level of sophistication to all the cabinets. Modern, elegant and practical, the Elite Collection brings functionality without compromising on style.

Prepac Black Elite Storage Set G - 8 Piece

Clear Deep Pour Epoxy Resin 1/2 - 1.5 layers

Laboratory Casework: Base Cabinets, Epoxy Tops

SIMIRON TableTop 1 Gal. Clear High-Gloss Protective Epoxy Coating 40005641 - The Home Depot

Deep Pour Epoxy for River Tables & Casting

Extra Deep Pour Resin Epoxy Kit (2 to 4 inch Pours), 1.5 GL, UV Resistant, Low Odor, Crystal Clear, Bubble Free, 2:1 Art Casting Resin, River Tables, Mold Making, Live Edge